arcor无线路由器使用skype出现的问题，奇怪！
现在用无线上网的机器打skype，过一会机器就和路由器接不上了，信号还是有，就是连接不上，必须重启路由器才能恢复，原来用其他牌子的路由器就没这个问题，现在用网线直联的机器也没有这个问题，不知道是怎么缘故？lidragon和其他高手们请支着啊，谢了！ 这个问题我以前说过了，
Arcor Wlan 100的Modem其实是用的ZyXEL出的 Prestige 660HW-67，http://www.zyxeltech.de/ ， 硬件上面是完全一样的，
但是Arcor的Modem用的Firmware很旧， 是去年9月的（v3.40.SQ0）， 后来官方版本已经升级2次了， 修复了好几十个Bug， 其中最重要的就是无线经常断的问题， 但是Arcor的Modem是不能升级官方版本的Firmware的， 因为不知道当初Arcor怎么和Zyxel签署的协议， 这个升级要Arcor出钱买才行， 结果Aror就是不买， 所以。。。。
网上有办法把Arcor的Modem通过一根数据线绕过刷机的限制升级成真正的ZyXEL Firmware， 然后以后就可以和ZyXEL出的 正版Prestige 660HW-67一样免费升级Firmware了
我的Arcor Modem已经被我刷成ZyXELModem了， 呵呵
[ 本帖最后由 lidragon 于 2005-7-19 18:55 编辑 ] http://www.dolc.de/forum/attachments/IMG_3673a_YCvMSBBAVbOK.jpg
我刷机用的线
http://www.dolc.de/forum/attachments/IMG_3672a_rzuGHzZcCeTk.jpg
打开Arcor Modem， 里面插线的地方
http://www.dolc.de/forum/attachments/IMG_3670a_dR6qxncCnbpX.jpg
刷机用的是Windows自己带的超级终端
http://www.dolc.de/forum/attachments/Snap1_MUWbfZAjAqMF.gif
刷好后看到版本变成了官方版本QD， 不再是Arcor的SQ了 在Arcor WLan 100的 Firmware之后Zyxel官方版本又修复的Bug和新增加的功能 List
Modifications in V 3.40(QD.6)D0 | 4/7/2005
1. Change to FCS version.
Modifications in V 3.40(QD.6)b3 | 3/23/2005
Modifications in V 3.40(QD.6)b2 | 3/9/2005
1.
Symptom: No matter enable/disable SIP ALG, Windows messenger can login via sip protocol
Condition: (1) Disable SIP ALG using C/I command “ip nat service sip active 0”
340QD6D0 3/62
ZyXEL Confidential
(2) Windows Messenger on PC attached to LAN of Prestige can still login to SIP server successfully.
Modifications in V 3.40(QD.6)b1 | 2/25/2005
1.
Symptom: After switching from router mode to bridge mode in AOL wizard, ATWPPPOE will be blocked.
Condition: (1) Switch from router mode to bridge mode in AOL wizard.
(2)Using ATWPPPOE to connect to PPPoE server, but it will fail.
2.
Symptom: Get the value of OID 1.3.6.1.2.1.4.20.1.2 will cause system crash.
Condition: Using SNMP client to get the value of OID 1.3.6.1.2.1.4.20.1.2 will cause system crash.
3.
Displays setting of PPPoE pass through as enabled in AOL wizard whatever what the actual value is
4.
Cancel the limitation of all WEP key should be entered, if user doesn't enter all four WEP keys, default WEP key will be copied to the keys left blank.
Modifications in V 3.40(QD.5)D0 | 1/7/2005
2. Change to FCS version.
Modifications in V 3.40(QD.5)b3 | 1/4/2005
1.
Symptom: Germany Name of MBM reset button is not right.
Condition: N/A.
2.
Symptom: Enter special URL will cause device crash.
Condition: 1. Form LAN site, enter http://192.168.1.1/Forms/rpAuth_1?ZyXEL%20ZyWALL%
20Series<script>top.location.pathname=%20""</script> on browser, the device
will crash.
3.
Symptom: ATWPPPOE client can't be blocked in router mode.
Condition: N/A
Modifications in V 3.40(QD.5)b2 | 12/24/2004
1.
Change ESSID to “wireless”.
2.
Change F/W upgrade web page as customer requested.
Modifications in V 3.40(QD.5)b1 | 12/10/2004
1.
If device is in router mode, AOL 8.0 or 9.0 PPPoE clients are blocked and can’t pass through device while PPPoE pass through is enabled, but can pass through device while in bridge mode.
2.
Symptom: PPPoE LED’s action is not right.
Condition: When no username and password is entered or wrong username and
340QD6D0 4/62
ZyXEL Confidential
password is entered, PPPoE connection can’t be successful, but PPPoE LED will brink orange.
3.
Add NETBIOS filter for LAN to WAN and WAN to LAN in default romfile.
4.
Add C/I command “ipsec adjTcpMss off” and “ip tracertEnable 1” in autoexec.net of default romfile.
5.
Add check box of HEX and ASCII to select WEP key type in the advanced WLAN settings.
6.
Add check box for PPPoE pass through in each wizard.
7.
Symptom: MAC address with all zero can’t be filtered out by our wireless LAN MAC address filter.
Condition: (1). Change MAC address of B220 wireless card to all zero.
(2). Set wireless LAN MAC address filter’s default action to allowing associating while matching, set MAC address wanted to associate.
(3). Then the B220 card can associate with device.
8.
Symptom: F/W upgrade web page can be accessed without username/password.
Condition: F/W upgrade web page can be access via “http://ip address/rpFWUpload.html” without username and password.
9.
Add a reset bottom in first page of MBM configuration to restore to default MBM configuration.
10.
Add static DHCP feature.
11.
Symptom: wireless client can't get IP address from DHCP server of P660HW
Condition: wireless client sometimes can't get IP address from DHCP server of P660HW while switching from one AP to another.
12
Configure MBM to satisfy VOIP voice quality.
Modifications in V 3.40(QD.4)D0 | 11/1/2004
1. Change to FCS version.
2.
Remove filter setup 3 (“ATWPPPOE” filter) in menu 21.1 and menu 11.5.
Modifications in V 3.40(QD.4)b2 | 10/20/2004
12.
Add a filter rule to block PPPoE connection of AOL 8.0 and AOL 9.0 clients. ( "ATWPPPOE") if device is set to router mode. And pass through the connection while the device in bridge mode.
13.
Add a C/I command “ip tracertEnable” to control whether to let tracert ICMP packets
340QD6D0 5/62
ZyXEL Confidential
pass from inside to the outside and as well the answers to this packet without being ping-able form the outside.
14.
Symptom: using Tiscali and Lycos wizard over WLAN does not work
Condition: . 660HW will store first WLAN-settings and activates them. In this case the user account will not be stored.
15.
Symptom &Condition: “Lycos/” should be changed to “lycos/” for a small “L” is needed, big “L” will not work.
16.
Symptom: user name can’t be fetched from romfile in other ISP wizard.
Condition: (1)Setup user name and password in other ISP,
(2) Go through the Wizard
(3)return to the other ISP wizard, user name can’t be fetched.
17.
Symptom: In the Lycos wizard, “\” is used in the username, but it should be “/”
Condition: Input username and password in the Lycos wizard, you will see “\” in the username in status page.
18.
Symptom: encapsulation type can’t be changed in WAN menu.
Condition: When change the encapsulation type to other type not same as original type, after page reload, it keeps as original value.
19.
Symptom: after finishing the wizards Tiscali, Lycos and other ISP, page will redirect to AOL, it should be redirected to first page.
Condition: after going through Tiscal, Lycos and other ISP, if everything is successful, the page will redirect to AOL wizard page.
20.
Symptom: there is a space in username field of Tiscal wizard, it will cause the total user name error and can’t dial up.
Condition: : there is a space in username field of Tiscal wizard, it will cause the total user name error and can’t dial up.
21.
Change "Übersicht" to "Einrichtungsassistent" in the main menu.
11. Add some words in Tiscal wizard.
Modifications in V 3.40(QD.4)b1 | 9/22/2004
1.
Add media bandwidth management with PPPoE pass through support.
2.
Add Tiscali and Lycos wizard web page in GUI.
3.
Symptom:. SIP pass through can’t work.
Condition: The SIP ALG do not process the "SIP INFO" message. And some of the fields in SIP message do not be transfered by ALG.
4.
340QD6D0 6/62
ZyXEL Confidential
change the F/W update page in the GUI as customer requested.
5.
Change default romfile to setup PPPoE pass through yes as default setting.
6.
Provide F/W version info in the first page of eWC.
7.
Change LED (DSL/PPP)’ action as customer requested:
DSL/PPP Off: No Adsl connection. DSL/PPP flashes green: Modem is synchronising DSL/PPP green on: synchronisation is established, no active pppoe connection.
DSL/PPP orange on: pppoe connection is established. DSL/PPP flashes orange: pppoe connection is established, and data is being transmitted.
[ 本帖最后由 lidragon 于 2005-7-19 19:03 编辑 ] 哈哈，高手！ 自己做了一个刷机线，但不知道线头的接法对不对，不敢轻举妄动，怕把设备烧了。还请lidragon指教，谢谢！ 原帖由 多客科技 于 2005-7-20 11:15 发表
自己做了一个刷机线，但不知道线头的接法对不对，不敢轻举妄动，怕把设备烧了。还请lidragon指教，谢谢！
一般都是用手机的数据线作的，因为手机的数据线里已经有集成电路了， 如果光用串口线， 还要自己焊个集成电路上去
一共有4个接头（其实是5个， 有一个是空的）
从左到右
1。 MASA
2。 空
3。 RX
4。 TX
5。3.3V
3,3V是没用的， 不用接
所以只要找一个有4个头的接头， 然后接成 MASA， 空， RX,TX 就可以了
插上的样子可以看我上面贴过的图
[ 本帖最后由 lidragon 于 2005-7-20 19:32 编辑 ] 串口线+集成电路的做法
[ 本帖最后由 lidragon 于 2005-7-20 19:32 编辑 ] 用C55 USB手机线的做法
图上画出来了， 地线都是2, 然后TX和RX要交叉一下
我自己用的是用串口的手机线做的
[ 本帖最后由 lidragon 于 2005-7-20 19:36 编辑 ] 楼上的真强！！！
页:
[1]
2