|
http://www.iphonehacks.com/2007/12/jailbreak-iphon.html#comments
iPhone Hackers Publish Simpler Method to JailBreak iPhone Firmware v1.1.2
偶不知道楼主的。1。12是不是美国版本的?如果是,现在已经可以完美破解了。先降级,然后破解。国内好像也是这么干的。
Please find below the 23-steps to JailBreak iPhone v1.1.2 courtesy iPhone Atlas:
Download the iPhone 1.1.1 firmware/software package, and after it is downloaded, make sure it still has the extension .ipsw and not .zip. Rename it if necessary (the correct name is iPhone1,1_1.1.1_3A109a_Restore.ipsw).
Put iPhone in recovery mode (hold the sleep and home [on the top of the iPhone] buttons simultaneously until the screen goes blank, then release the sleep button but keep holding the home button until a screen showing an iTunes icon and a USB cable appears).
Launch iTunes if it isn’t open. You will receive a message that says “iTunes has detected an iPhone in recovery mode”
Do not restore the iPhone at this point
In iTunes, select your iPhone from the left-hand pane (source list) and click the “Summary” tab. Hold down the option key, then click “Restore.” Select the 1.1.1 package you just downloaded. You’ll receive the error message “1015″ indicating a failure to restore — this is normal.
Download the iTunes 1.1.2 jailbreak folder from Conceited Software.
If you are using a Mac, double-click jailbreak.jar in the file you just downloaded. If you are on a Windows system, double-click the file windows.bat. Click the “Boot from Recovery” button. This should force the iPhone out of recovery mode.
This process can take several minutes. In our case, the progress bar never finished, but the proper process occurred — if it works, your iPhone screen will go completely black and the device will power off. At this point, you should hold down the power buttonfor several seconds until the device restarts. If 10 or minutes have gone by and nothing has happened (the recovery mode screen, with an iTunes icon and a USB cable, is still displayed on your iPhone), try disconnecting your iPhone and reconnecting it and trying again.
You will no see the “Waiting for Activation” screen, but your iPhone won’t activate.
Slide to unlock your iPhone, and launch Safari.
Navigate to www.jailbreakme.com.
Go to the bottom of the page and tap “Install AppSnapp.”
You will see the “Downloading Programs” message and a spinning progress indicator.
At the end of the process, your iPhone will be jailbroken under firmware version 1.1.1, but you won’t have access to voice services yet.
Slide to unlock your iPhone. You will see the “Installer” icon on your home screen. Tap it.
Tap “Install” at the bottom of the screen, then tap “Tweaks 1.1.1″
Scroll down to a package called “OktoPrep” and tap it, then tap the “Install” button in the upper-right corner.
In iTunes, select your iPhone from the source lift on the left-hand side. If it prompts you to restore your iPhone from backup, you can do so (by pressing the “Continue” button), after which your iPhone will reboot and again try (and fail) to activate.
With your iPhone selected on the left-hand pane, click the “Summary” button a the top of the window. You will see a message stating “A newer version of the iPhone software is available (1.1.2). […]” Click the Update button (not Restore). Your iPhone should receive the 1.1.2 update, and eventually activate in iTunes.
[At the end of the process, you might see an error message indicating that the iPhone could not be restored because of an “Error 1602″ or similar. If so, follow the instructions in this Knowledge Base article to re-install iTunes. You then, unfortunately, have to start the process all over again.]
After the installation of firmware 1.1.2, Installer will vanish from your iPhone — this is normal.
Go back to the folder you downloaded from Conceited Software and again run the jailbreak.jar file on a Mac or the windows.bat file on a Windows system. This time, check the “Install SSH option” then press the “Jailbreak” button. This process takes several minutes — do not perform any other operations on your iPhone during this process.
Your iPhone will reboot several times. When you’re done, the Installer application should now be on your screen and the iPhone should properly activate. Consult our Applications page for information on using Installer.
$握手$ $握手$
如果参与讨论的不是马甲,应该是没有问题,这个还比较新,但是通读下面的评论,发现有的人行,有的人不行。有的人说超级简单,有的人不停的寻求帮助,因为中途出现问题,不知道该怎么帮,建议楼主等等,不会超过几个星期,就会有更完美的破解,偶纯属纸上谈兵,因为我的IPHONE在路上。
[ 本帖最后由 二锅头头 于 2007-12-12 22:25 编辑 ] |
|